{"product_id":"dfrobot-gravity-dfr0971-gp8403-two-channel-i2c-dac","title":"DFRobot Gravity DFR0971 GP8403 2-Channel I2C DAC Module 0-5V 0-10V","description":"\u003ch2\u003eDFRobot Gravity DFR0971 GP8403 Dual-Channel I2C DAC\u003c\/h2\u003e\u003cp\u003eAdd two programmable analog voltage outputs to a compatible microcontroller. This GP8403-based module converts I2C commands into 0–5 V or 0–10 V control signals for equipment with matching analog control inputs. It is useful for dimmer control, automation prototypes and low-frequency test signals.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eConnection note:\u003c\/strong\u003e These are voltage control outputs, not motor or lamp power terminals. Connect them to the equipment's compatible control input and use the equipment's separate power supply as required. Confirm signal limits and grounding before connecting. This is not the separate DFRobot 4–20 mA current-output DAC.\u003c\/p\u003e\u003ch3\u003eFeatures and specifications\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003ctd\u003eDFRobot Gravity DFR0971\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDAC chip\u003c\/th\u003e\n\u003ctd\u003eGP8403\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eChannels\u003c\/th\u003e\n\u003ctd\u003eTwo analog voltage outputs, VOUT0 and VOUT1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutput ranges\u003c\/th\u003e\n\u003ctd\u003e0–5 V or 0–10 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eResolution\u003c\/th\u003e\n\u003ctd\u003e12-bit, codes 0x000–0xFFF\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSupply\u003c\/th\u003e\n\u003ctd\u003e3.3–5 V DC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInterface\u003c\/th\u003e\n\u003ctd\u003eI2C through PH2.0 four-pin Gravity connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eI2C logic high level\u003c\/th\u003e\n\u003ctd\u003e2.7–5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eI2C addresses\u003c\/th\u003e\n\u003ctd\u003e0x58–0x5F, selected with A0\/A1\/A2 DIP switches\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutput voltage error\u003c\/th\u003e\n\u003ctd\u003eLess than 0.5%, maker specification\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutput linearity error\u003c\/th\u003e\n\u003ctd\u003e0.1%, maker specification\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eModule consumption\u003c\/th\u003e\n\u003ctd\u003eLess than 4 mA, not an output load-current rating\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProtection\u003c\/th\u003e\n\u003ctd\u003eOutput short-circuit protection, per maker\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003ch3\u003eAddress selection\u003c\/h3\u003e\u003cp\u003eThe DIP switches allow eight distinct addresses, so eight modules can share an I2C bus without address conflicts, providing up to sixteen output channels. Check the A0\/A1\/A2 address table printed on the rear of the board or in the official wiki. The library example uses 0x58.\u003c\/p\u003e\u003ch3\u003eConnection and first use\u003c\/h3\u003e\u003cp\u003eConnect the Gravity supply and ground to a compatible controller supply, and connect its data and clock lines to the controller's I2C SDA and SCL pins. Connect the output terminal's ground and the chosen VOUT0 or VOUT1 to the receiving device's analog control input. Check the receiving device's required voltage range before enabling an output.\u003c\/p\u003e\u003cp\u003eUse the DFRobot_GP8403 library to initialize the module, select the 5 V or 10 V output range, then set the output code for channel 0, channel 1 or both. Select the output range in software rather than assuming the supply voltage sets it. The library's store function saves a chosen output setting for later power-up; ordinary changes are not retained through a power cycle unless saved.\u003c\/p\u003e\u003cp\u003eThe official brightness example uses a separate 0–10 V LED dimmer and its own load power supply. Those parts are not included. The waveform example demonstrates a 10 Hz sine wave; it does not establish a general high-speed signal-generator specification.\u003c\/p\u003e\u003ch3\u003ePackage Includes\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e1 × DFRobot Gravity DFR0971 two-channel GP8403 DAC module\u003c\/li\u003e\n\u003cli\u003e1 × Gravity I2C\/UART sensor connector cable\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eController, dimmer, load and power supply are not included. The cable's I2C\/UART name does not add UART support to this I2C module.\u003c\/p\u003e\u003ch3\u003eUseful Links\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.dfrobot.com\/product-2613.html\"\u003eOfficial product specifications and package\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/wiki.dfrobot.com\/dfr0971\/\"\u003eDFR0971 pinout and DIP-switch address table\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/wiki.dfrobot.com\/dfr0971\/docs\/19830\"\u003eArduino dimmer wiring and setup example\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/wiki.dfrobot.com\/dfr0971\/docs\/19829\"\u003eArduino 10 Hz sine-wave example\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/wiki.dfrobot.com\/dfr0971\/docs\/19828\"\u003eLibrary reference\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/github.com\/DFRobot\/DFRobot_GP8403\"\u003eOfficial DFRobot GP8403 library\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"DFRobot","offers":[{"title":"Default Title","offer_id":51936416628903,"sku":"IN000384","price":1148.31,"currency_code":"INR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0618\/9042\/9095\/files\/DFR0971_Main_01.jpg?v=1795130952","url":"https:\/\/rees52.com\/products\/dfrobot-gravity-dfr0971-gp8403-two-channel-i2c-dac","provider":"REES52","version":"1.0","type":"link"}