Multifunction Self-Lock Relay Cycle Timer Module PLC Automation Delay FRM03 8V-32V - RS1796

0 Review(s)

Rs 700

RS1796

New product

  • Operating voltage: recommended DC 8-32V
  • The minimum set of 0.1 seconds timing function
  • Operating temperature: recommended -20 – 60-degree celsius
  • PACKAGE INCLUDED: 1 x 

More details

By buying this product you can collect up to 7 loyalty points. Your cart will total 7 loyalty points that can be converted into a voucher of Rs 7.


FUNCTION

  • Function 1: Timing Pick: After power relay delay time T1, T1 in 0 seconds adjustable between -270 hours, give CH1 connector is a high pulse signal(high duration is greater than or equal 20ms, hereinafter the same), repeat the above functions.
  • Function 2: Timed disconnect: On power relay, time relay off delay time T1, T1 in 0 seconds adjustable between -270 hours, giving a high level pulse signal CH1 connector, repeat the above functions.
  • Function 3: Loop Timing Mode 1: After power on, to not pull the relay, the delay time T1 after arrival relay; pull the relay off time T2 after arrival, and then repeat the above state, the delay time T1 and T2 in 0 seconds adjustable between -270 hours, giving a high level pulse signal CH1 connector, you can resume these functions.
  • Function 4: Loop Timing Mode 2: After power, the relay immediately pull, delay time T1 after arrival relay off; off time T2 arrives relay, and then repeat the above state, the delay time T1 and T2 in 0 seconds - adjustable between 270 hours and give CH1 connector is a high pulse signal, these functions can be re-started.
  • Function 5: Latching relay mode: CH1 connector to relay a high level pulse signal, the relay, to give a high level pulse signal relay disconnected.
  • Function 6: Self-locking relay mode: to the relay X interface a high (low) level pulse signal, the relay pull, and then to a high (low) level pulse signal, the relay disconnected.
  • Function 7: Level trigger relay mode (including delay disconnect function): when power on, relay disconnect, gives the X interface a high (low) level signal, the relay immediately pull, after X port signal disappears, the relay is still pull, after T1 time in pull, the relay disconnect, T1 can be adjusted between 0.1 seconds -270 hours.
  • Note: in this function, if the T1 is set to 0 seconds, it becomes: if the X port has a high (low) level signal, relay pull, if no signal it will immediately disconnected.
  • Function 8: Trigger timing pull: when power on, relay disconnect, gives the X interface a high (low) level pulse signal, delay T1 time, relay pull. T1 can be adjusted between 0.1 seconds -270 hours. Repeat to the X interface a high (low) level pulse signal, repeat this function again.
  • Function 9: Trigger timing disconnection: when power on, relay disconnect, gives the X interface a high (low) level pulse signal, relay pulls, after T1 time, relay disconnect. T1 can be adjusted between 0.1 seconds -270 hours. Repeat to the X interface a high (low) level pulse signal, repeat this function again.
  • Function 10: Trigger timing pull and then disconnect: when power on, relay disconnect, gives the X interface a high (low) level pulse signal, after T1 time, relay pull, after T2 time, relay disconnect. T1 and T2 can be adjusted between 0.1 seconds -270 hours. Repeat to the X interface a high (low) level pulse signal, repeat this function again.
  • Function 11: Trigger timing disconnect and then pull: when power on, relay disconnect, gives the X interface a high (low) level pulse signal, relay pull, after T1 time, relay disconnect, after T2 time, relay pull. T1 and T2 can be adjusted between 0.1 seconds -270 hours. Repeat to the X interface a high (low) level pulse signal, repeat this function again.
  • Function 12:Infinite cycle mode 1: when power on, relay disconnect, gives the X interface a high (low) level pulse signal, delay T1 time, relay pull, after T2 time in pull, relay disconnect, and then repeat the above action. T1 and T2 can be adjusted between 0.1 seconds -270 hours, and repeat to give X interface a high (low) level of the pulse signal, the above function can start again.

MODULE INTERFACE

  • Module control side: there are 3-wire interface, all interfaces are terminal, user-friendly.
  • DC+: DC power supply positive(with 5V, 12V and 24V modules to choose from).
  • DC-: DC power cathode.
  • CH1: Hold Input Detection Interface.
  • Relay outputs: A 3-wire interface, all interfaces are terminals.
  • NO1: normally open relay interface, the relay becomes vacant before, pull shorting after the COM1.
  • COM1: Relay Common Interface.
  • NC1: normally closed relay interface relay shorted before and COM1, pull vacant post.

PACKAGE INCLUDED

  • 1 x Multifunctional relay module

No customer reviews for the moment.

Write a review

30 products in category:

Compare